How To Replace Lg G6 Camera Glass
Introduction
Utilize this guide to replace the cameras on your LG G6.
-
-
For reference, the backside of the console is shown in the first photo. Notation the clearance between the edge of the panel and the delicate ribbon cablevision abreast the fingerprint sensor.
-
Be careful as y'all slice and pry to the left side of the fingerprint sensor, as seen from the exterior of the phone in the third photograph.
-
-
-
Use a hairdryer, a rut gun, or gear up an iOpener and apply it to the lower edge of the G6 for about a minute to soften up the adhesive underneath the rear drinking glass panel.
-
-
-
Secure a suction cup to the rear panel, as close to the heated border equally possible.
-
-
-
If y'all don't have a small object for propping, you tin can (carefully) perform this step at the edge of a desk-bound or table to accomplish the aforementioned angle of entry.
-
Lift the rear panel's bottom edge with your suction cup, opening a slight gap betwixt the panel and the frame.
-
Once y'all've created a gap, press the apartment end of an opening tool into the gap.
-
-
-
Slide the opening tool dorsum and along across the bottom border of the phone, cut through the agglutinative securing the rear drinking glass panel.
-
In one case the agglutinative is cut and the gap is wide enough, insert an opening pick into the gap to keep the agglutinative from re-bonding. Remove the opening tool.
-
-
-
Additionally, y'all tin use multiple opening picks for this process, leaving i in identify on each side after you end slicing to preclude the adhesive from re-adhering as information technology cools.
-
Slide the opening pick along the left border of the phone to slice through the adhesive securing the rear panel.
-
-
-
Re-insert the opening pick into the bottom border of the phone and slide information technology upwardly the right edge of the phone, cutting through the adhesive property information technology in place.
-
-
-
Carefully slide an opening pick across the top edge of the phone, separating the final of the adhesive securing the rear glass panel.
-
-
-
One time all the agglutinative is cutting, use an opening pick to pry up the rear glass panel.
-
Remove the panel.
-
-
-
Use tweezers to pare away any remaining adhesive from both the rear panel and the phone'due south chassis.
-
Make clean the adhesion areas with high concentration isopropyl alcohol (at to the lowest degree 90%) and a lint-free cloth. Swipe in one direction simply, non back and forth. This volition help prep the surface for the new adhesive.
-
Pare away the replacement adhesive's liner, marshal it with the dorsum of the phone, and press it into place.
-
Remove any remaining liners, and replace the rear glass console.
-
After installing the rear panel, apply strong, steady pressure to your phone for several minutes to assistance the adhesive form a good bond, such as by placing it under a stack of heavy books.
-
-
-
Remove the four Phillips screws belongings downwards the lower antenna shield.
-
-
-
Insert the point of a spudger into the pocket-sized gap betwixt the lower antenna shield and the metallic frame of the phone.
-
Gently pry up the antenna shield and remove it from the phone.
-
-
-
Remove the seven Phillips screws belongings downwards the upper antenna shield.
-
-
-
Insert the flat end of a spudger into the small gap between the upper antenna shield and the phone chassis and pry up, releasing the clips property the shield in place.
-
Remove the upper antenna shield and wireless charging coil.
-
-
-
Use a spudger to pry upwardly the printing connector at the end of the battery's ribbon cablevision, disconnecting the battery.
-
-
-
Insert a SIM removal tool or the SIM removal bit into the hole opposite the book buttons and printing to release the SIM/MicroSD carte tray.
-
Remove the SIM/MicroSD tray.
-
-
-
Use the flat finish of the spudger to elevator up the two printing connectors on the bottom end of the motherboard higher up the USB-C port.
-
-
-
Remove the sticker connecting the motherboard to the vibration motor.
-
-
-
Grab the motherboard by the top finish (the stop with the cameras) and gently lift it up and out of the phone.
-
-
-
Remove the two rear-facing and front-facing cameras from the motherboard.
-
Conclusion
To reassemble your device, follow these instructions in opposite order.
Embed this guide
Choose a size and copy the code below to embed this guide every bit a small widget on your site / forum.
Preview
Source: https://www.ifixit.com/Guide/LG+G6+Cameras+Replacement/98939
Posted by: millerthatert.blogspot.com
0 Response to "How To Replace Lg G6 Camera Glass"
Post a Comment